PROFIBUS dp/v1 fieldbus coupler 12 mbaud digital and analog signals. Part #, Manufacturer, WAGO. GTIN, Condition, New. Quantity . Accessory Type: Fieldbus Coupler. Current Rating: mA. Current Rating: mA. External Depth: mm. External Depth: mm. External Width: 51mm. Hi everyonei’m a beginer and i’m trying to connect wago I/O system with CPU CDP But I Don’t know where i did the mistake i.
|Published (Last):||3 January 2015|
|PDF File Size:||10.69 Mb|
|ePub File Size:||2.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
WAGO : User manual
The manufactiuring number inscribed on the side of the module contains the FW L number of the 705-333. They are located on either side of the modules.
The right hand LED C signals the supply to the field side, i. The service to be provided is requested by the Client. In line with the maximum surface temperature for all ignition protection types, the electrical components are subdivided into temperature classes, as far as electrical components of explosion protection group II are concerned.
In the reply telegram of the diagnosis selection the identification based diagnosis and the device status are transmitted together with the standard diagnosis.
In this manner sensors and actuators can be supplied and fused by a separate voltage source. Follow us on Twitter Youtube.
Device supply is intended for system supply and field side supply. New question published by pharaz is split to a separate thread with wao subject wago ?
Display elements 3. With diagnosis capable terminals the diagnosis message can be suppressed or released for a channel or module. Hope this helps, Daniel Chartier. Structure, content and coding of this device master data are standardised so that projecting with any DP slaves with projecting data from various manufacturers is possible. Male contacts are located on the left-hand side of the bus modules. The modules are configured when projecting the nodes.
With input modules counter2 bytes follow which are reserved for future options. Hello Karim; The manufactiuring number inscribed on the side of the module contains the FW L number of the module. Power supply 24V g01xx02x 1 — Power supply System 2 — Power supply Field-side The power supply on the field side is electrically isolated from the system supply. Only disconnect the equipment when the power supply has been switched off or the area is known to be a non-explosive area.
Select the configuration that is closest to the range of FW in th configuration settings. Attention Switch off the system prior to working on bus modules! The line type B also described in the EN 50 is an old type and should no longer be used. Analog inputs are followed by 2 bytes reserved for future options. Bus connection gd Note When connecting the subscriber ensure that the data lines are not mixed up.
Parameter Value Wave resistance Attachment Wago Firmware version. The power supply is limited to a maximum value.
The others contain manufacturer specific parameters. To isolate the modules to the right of the power supply, the fuse can be removed from the fuse holder. With analog inputs 2 bytes follow which are reserved for future options. In the reply telegram of the diagnosis selection, in addition to the standard diagnosis at least the identification based diagnosis and the device status are transmitted.
Server Serving device within a Client Server System. Wago sample configuration. Site Explorer Site Explorer. Your manual failed to upload There are digital and analog inputs and outputs and modules for special functions Counter modules, Terminal blocks for encoder and resolvers and communication modules. Have a look at the Diagnostics section of the manual, the first part shows how to evaluate an error based on the diagnostic LED status:.
For output modules PWM output 6 byte parameterisation data follow, used for saving the substitute values for a maximum of 2 channels 2 words. By the way, the end module is required to terminate the IO bus of the Wago modules, but is not part of the configuration.
What’s missing? Tell us about it.
The fieldbus coupler or the process data channel is to be configured on the first slot. Valid station addresses are between 1 and The bus line comprises of a twisted and screened pair of wires. The fieldbus coupler does not use the process data channel. All about Decentral Peripherie.
Explosive Environments Identification acc. To fix, insert a screwdriver into the top groove of the locking disc and press. Self-cleaning power jumper contacts P. Hello Karim; Please look at the following discussion on the Siemens forum, specially the last one: