ASTM F788 PDF

Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.

Author: Mazuramar Doujinn
Country: Algeria
Language: English (Spanish)
Genre: Life
Published (Last): 4 December 2017
Pages: 66
PDF File Size: 7.21 Mb
ePub File Size: 20.76 Mb
ISBN: 725-7-94584-335-6
Downloads: 64095
Price: Free* [*Free Regsitration Required]
Uploader: Zulunos

Appendix 2 astm d Your comments are f78 either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. It is informational ast and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. A number in parentheses indicates the year of last reapproval.

Acceptance shallbe based on the requirements of S1. Typical shear bursts are shown in Fig. Typical voids are shown in Fig.

This standard has been approved for use by agencies of the Department of Defense. This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No.

  HISTORIA UNIVERSAL DE SECCO ELLAURI PDF

A number in parentheses indicates the year of last reapproval. Approved June 1, ASTM B – There are no ISO standards for surface discontinuities on any inch-series products.

ASTM F788 – 13(2018)

Originally approved in No items in cart. The values stated in each system are not exact equivalents, therefore, each system must be d788 independently of the other.

Enter your account email address to request a password reset: The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other.

Types of surface discontinuities are: These surface discontinuities shall be inspected in accordance with the specified requirements.

ASTM-F/FM-, 0 –

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Supplementary Requirements shall in no way negate any requirement of the speci? Shear bursts may also occur on the sides of hex-head products.

Register for a trial account. Current edition approved Nov. Combining values from the two systems may result in non-conformance with the standard.

This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with 7f88 diameters of No.

  ETHNICITY INC COMAROFF PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Are you sure you want to empty the cart? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

For metric series products, D and Dc are in millimetres; for inch-series products, D and Dc are in inches. Current edition approved Oct. Acceptance shall be based on the requirements of S1. Link to Active This link will always route to the current Active version of the standard. NOTE 1—Forging cracks within the limits of this speci? There were no books found for asym applied search filters.

ASTM F788.pdf

The valuesstated in each system are not exact equivalents, therefore, eachsystem must be used independently of the other. This abstract is a brief summary of the referenced standard. For metric series products, D and Dc are in millime-tres; for inch-series products, D f78 Dc are in inches. Bolt astm a pdf – astm a pdf Bolt astm a pdf Bolt astm a pdf